How do I fix the E20 error on my Electrolux washing machine?

Resolution

1. Ensure the drain hose is in the correct position.
2. Ensure correct drain height.
3. Clean the pump and filter.
4. Check for a blocked drain.
5. Check the drainage hose for possible kink or twist.
6. Use less soap powder.
7. Switch off the power to the washing machine.
8. Contact an Authorised Service Center.

What does E20 mean on Electrolux washing machine?

Washer dryer displays error message E20 or C2, emits 2 beeps or 2 flashes. It indicates pumping problems. Washer dryer does not drain. The drum does not turn. The appliance makes an unusual noise because of the blockage of the drain pump.

How do I reset my E20 washing machine?

You can fix this by switching off the machine and shaking the drum forwards and backwards several times. Clean the drain pump/filter and then run a hot wash without any soap powder. 2. Switch off the power to the machine.

Why is my washer saying E20?

On some models an obstruction or blockage in the drain pump may cause E20 to appear in the display.

How do I force my Electrolux washer to drain?

A common cause for a washer not draining is that the drain pump is impeded or defective.

1. Disconnect the hoses connected to the drain pump.
2. If required, unscrew the drain pump.
3. Unplug the electrical connector.
4. Check the impeller on the pump for obstructions.
5. Use a multimeter to test the pump for resistance.

How do you manually drain an Electrolux washing machine?

If your washing machine doesn’t have an external filter or if the above hasn’t worked:

1. Run a spin/drain programme.
2. Unplug the appliance.
3. Close the tap.
4. Put the two ends of the inlet hose in a container and let the water flow out of the hose.

How do I drain the water from my Electrolux washing machine?

How do I drain my Electrolux washing machine?

How do I drain my Electrolux front load washer?

Remove the hose from the washer, and check for blockages. Clean the hose with hot water; a drain snake; or a vinegar, water, and baking soda mixture.

How do you force Electrolux to drain?

Check the drainage hose has no kinks

1. Open the pump cover – some of these will open with a push while others may require a small coin in the small indent to pull it open.
2. Turn the filter 180 degrees in an anti-clockwise direction to open it, without removing.

How do you force drain an Electrolux washing machine?

Why won’t my Electrolux washer drain?

A common cause for a washer not draining is that the drain pump is impeded or defective. Disconnect the hoses connected to the drain pump. If required, unscrew the drain pump. Unplug the electrical connector.

How to fix Electrolux washing machine error code E20?

E20 is one of the most frequent Electrolux washing machine error codes. Electrolux washing machine E20 error appears when the washing machine has detected that the water has not drained in the programmed time. Check drain pump filter for blockages. Check drain hoses for blockages and kinks. Inspect wiring for breaks. Replace drain pump.

What does EF4 mean on my Electrolux washing machine?

Electrolux washing machine EF4 error is very similar to E10 error, they are both inlet faults. But EF4 is directly related to the flow meter, so if your washing machine is actually filling well through all inlet valves, it could be just a faulty flow meter reed switch.

What does E35 mean on my Electrolux washing machine?

The E35 error code in your Electrolux washing machine indicates that the machine is overfilling. The most common culprit is the water level switch. Here’s how to replace this part…

Why is my Electrolux washing machine not filling up with water?

Washing machine is not filling with water. This is one of the most common Electrolux washing machine error codes. In most cases it’s just a closed tap or a kinked hose that has caused this error to appear. In rare cases your washing machine might need a new water inlet valve.