How do I set an ASA username and password?

How do I set an ASA username and password?

To set the enable password on your Cisco ASA 5505:

1. Get into the command line. I prefer using the console cable to directly connect.
2. Hit enter a few times to get the prompt.
3. Type ‘ena’ to enter enable mode.
4. Type ‘config t’ .
5. Type ‘enable password PaSsWoRd’ , replacing the second, ‘PaSsWoRd’ with desired password.

What is the Cisco ASA default password?

IP Address
Username	Cisco
Password	Cisco
SSID

How do I reset my ASA firewall?

1. After you open connection, press enter a couple of times, and you should get a prompt like: ‘ciscoasa>’
2. type ‘enable’ to go to enable mode.
3. type ‘config t’
4. type ‘config factory-default’
5. hit spacebar when the ‘more’ is displayed.
6. type ‘reload save-config noconfirm’

How do I find my cisco ASA encrypted password?

Normally, you use the ‘show run’ command to view the running configuration. Pre-shared keys are marked with an asterisk (*). To view the password unencrypted, type ‘more system:running-config’. This will display the full configuration with unencrypted passwords.

How do I assign an IP address to a firewall in Asa?

Set a Static IP for your Cisco ASA5505 Firewall

1. Open the ASDM and log into your device.
2. Under Configuration, Interfaces, select the Outside interface and hit Edit.
3. In the ‘IP Address’ box, click the radio for ‘Use Static IP’
4. Select an IP address, and use ‘255.255.
5. Hit ok, then apply.

How do I reset my cisco ASA password?

To recover passwords for the ASA, perform the following steps:

1. Step 1 Connect to the ASA console port according to the instructions in “Accessing the Command-Line Interface” section.
2. Step 2 Power off the ASA, and then power it on.
3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

How do I reset my ASA 5510 to factory settings?

Resetting a Cisco ASA 5510 to Factory Defaults

1. Connect your console cable and make sure you can see the command prompt for the ASA – even if you can’t log in.
2. Power cycle the appliance – flick the power switch on the front off and on again.

How to factory reset a Cisco ASA 5512-X IPS?

How to Factory Reset a Cisco ASA 5512-X IPS. At the console prompt ciscoasa> type enable (press enter) If prompted, enter your password and press enter (the default password is nothing, just press enter). Type: # configure terminal (press enter) Type: # configure factory-default (press enter) Type:

How do I connect my Asa 5512-X to my computer?

Step 1. Connect to the Cisco ASA 5512-X IPS with the serial over ethernet cable. This is otherwise known as the console cable. In most cases, it’s long, thin and light blue in colour. Connect the RJ45 end to the console port of the Cisco ASA 5512-X IPS and the other end to a computer or laptop with a serial port.

What is the default configuration for the ASA FirePower module?

The ASA ships with a default configuration that enables Adaptive Security Device Manager (ASDM) connectivity to the Management 0/0 interface. When you use a software module such as the ASA FirePOWER module, we recommend that you do not use the default configuration, which can preclude the ASA FirePOWER module from reaching the Internet for updates.

What licenses are included in the ASA 5512-X and Asa 5515-X?

The ASA 5512-X includes the Base or Security Plus license, depending on the version you ordered. The ASA 5515-X through 5555-X includes the Base license. You can optionally purchase the following licenses: They also come pre-installed with the Strong Encryption (3DES/AES) license if you qualify for its use.